Research Papers: Fundamental Issues and Canonical Flows

Characterization of Ion Transport and -Sorption in a Carbon Based Porous Electrode for Desalination Purposes

[+] Author and Article Information
Carlos Hidrovo

Assistant Professor
e-mail: hidrovo@mail.utexas.edu
Department of Mechanical Engineering,
The University of Texas at Austin,
Austin, TX 78712

1Corresponding author.

Manuscript received September 3, 2012; final manuscript received December 14, 2012; published online February 22, 2013. Assoc. Editor: Prashanta Dutta.

J. Fluids Eng 135(4), 041201 (Feb 22, 2013) (8 pages) Paper No: FE-12-1430; doi: 10.1115/1.4023294 History: Received September 03, 2012; Revised December 14, 2012

New and more efficient water desalination technologies have been a topic of incipient research over the past few decades. Although the focus has been placed on the improvement of membrane-based desalination methods such as reverse osmosis, the development of new high surface area carbon-based-electrode materials have brought substantial interest towards capacitive deionization (CDI), a novel technique that uses an electric field to separate the ionic species from the water. Part of the new interest on CDI is its ability to store and return a fraction of the energy used in the desalination process. This characteristic is not common to other electric-field-based desalination methods such as electro-deionization and electrodialysis reversal where none of the input energy is recoverable. This paper presents work conducted to analyze the energy recovery, thermodynamic efficiency, and ionic adsorption/desorption rates in a CDI cell using different salt concentration solutions and various flow rates. Voltage and electrical current measurements are conducted during the desalination and electrode regeneration processes and used to evaluate the energy recovery ratio. Salinity measurements of the inflow and outflow stream concentrations using conductivity probes, alongside the current measurements, are used to calculate ion adsorption efficiency. Two analytical species transport models are developed to estimate the net ionic adsorption rates in a steady-state and nonsaturated porous electrode scenario. Finally, the convective and electrokinetic transport times are compared and their effect on desalination performance is presented. Steady test results for outlet to inlet concentration ratio show a strong dependence on flow rate and concentration independence for dilute solutions. In addition, transient test results indicate that the net electrical energy requirement is dependent on the number of carbon electrode regeneration cycles, which is thought to be due to imperfect regeneration. The energy requirements and adsorption/desorption rate analyses conducted for this water-desalination process could be extended to other ion-adsorption applications such as the reprocessing of lubricants or spent nuclear fuels in a near future.

Copyright © 2013 by ASME
Your Session has timed out. Please sign back in to continue.


U.S. Census Bureau, 2012, “U.S. & World Population Clocks,” May 15, 2012, http://www.census.gov/main/www/popclock.html
Chenoweth, J., 2008, “Minimum Water Requirement for Social and Economic Development,” Desalination, 229(1–3), pp. 245–256. [CrossRef]
Anderson, M. A., Cudero, A. L., and Palma, J., 2010, “Capacitive Deionization as an Electrochemical Means of Saving Energy and Delivering Clean Water. Comparison to Present Desalination Practices: Will It Compete?” Electrochim. Acta, 55(12), pp. 3845–3856. [CrossRef]
Food and Agriculture Organization of the United Nations, 2010, “Freshwater Availability-Precipitation and Internal Renewable Water Resources (IRWR),” September 2012, http://www.fao.org/nr/aquastat
Welgemoed, T. J., and Schutte, C. F., 2005, “Capacitive Deionization Technology™: An Alternative Desalination Solution,” Desalination, 183(1–3), pp. 327–340. [CrossRef]
Oren, Y., 2008, “Capacitive Deionization (CDI) for Desalination and Water Treatment—Past, Present and Future (A Review),” Desalination, 228(1–3), pp. 10–29. [CrossRef]
Kamal, I., 2008, “Myth and Reality of the Hybrid Desalination Process,” Desalination, 230(1–3), pp. 269–280. [CrossRef]
Vial, D., and Doussau, G., 2003, “The Use of Microfiltration Membranes for Seawater Pre-Treatment Prior to Reverse Osmosis Membranes,” Desalination, 153(1–3), pp. 141–147. [CrossRef]
Voros, N. G., Maroulis, Z. B., and Marinos-Kouris, D., 1996, “Salt and Water Permeability in Reverse Osmosis Membranes,” Desalination, 104(3), pp. 141–154. [CrossRef]
Dermentzis, K., and Ouzounis, K., 2008, “Continuous Capacitive Deionization-Electrodialysis Reversal Through Electrostatic Shielding for Desalination and Deionization of Water,” Electrochim. Acta, 53(24), pp. 7123–7130. [CrossRef]
Lim, J.-A., Park, N.-S., Park, J.-S., and Choi, J.-H., 2009, “Fabrication and Characterization of a Porous Carbon Electrode for Desalination of Brackish Water,” Desalination, 238(1–3), pp. 37–42. [CrossRef]
Zhai, Y., Dou, Y., Zhao, D., Fulvio, P. F., Mayes, R. T., and Dai, S., 2011, “Carbon Materials for Chemical Capacitive Energy Storage,” Adv. Mater., 23(42), pp. 4828–4850. [CrossRef] [PubMed]
Park, K.-K., Lee, J.-B., Park, P.-Y., Yoon, S.-W., Moon, J.-S., Eum, H.-M., and Lee, C.-W., 2007, “Development of a Carbon Sheet Electrode for Electrosorption Desalination,” Desalination, 206(1–3), pp. 86–91. [CrossRef]
Zhao, R., Biesheuvel, P. M., Miedema, H., Bruning, H., and van der Wal, A., 2009, “Charge Efficiency: A Functional Tool to Probe the Double-Layer Structure Inside of Porous Electrodes and Application in the Modeling of Capacitive Deionization,” J. Phys. Chem. Lett., 1(1), pp. 205–210. [CrossRef]
Demirer, O. N., Naylor, R., Rios Perez, C. A., Wilkes, E., and Hidrovo, C., “Energetic Performance Optimization of a Capacitive Deionization System Operating With Transient Cycles and Brackish Water,” Desalination (submitted).
Biesheuvel, P. M., van Limpt, B., and van der Wal, A., 2009, “Dynamic Adsorption/Desorption Process Model for Capacitive Deionization,” J. Phys. Chem. C, 113(14), pp. 5636–5640. [CrossRef]
Rios Perez, C. A., Demirer, O. N., Clifton, R. L., Naylor, R. M., and Hidrovo, C. H., 2013, “Macro Analysis of the Electro-Adsorption Process in Low Concentration NaCl Solutions for Water Desalination Applications,” J. Electrochem. Soc., 160(3), pp. E13–E21. [CrossRef]


Grahic Jump Location
Fig. 4

(a) Outlet conductivity as a function of time for a transient test, and (b) circuit current as a function of time for a transient test

Grahic Jump Location
Fig. 3

Schematic of CDI cell

Grahic Jump Location
Fig. 2

(a) Actual experimental setup, and (b) schematic of the experimental setup

Grahic Jump Location
Fig. 1

(a) Overview of desalination cycle. Voltage difference applied across the electrodes induce opposite electrode charges to attract and adsorb the ions. (b) Overview of regeneration cycle. Ion concentration on the electrode surfaces decrease together with the electrode charge, due to current flow across the resistor.

Grahic Jump Location
Fig. 5

Control volume analysis for salt adsorption

Grahic Jump Location
Fig. 7

Energy recovery based on cycle number

Grahic Jump Location
Fig. 6

Ion movement in CDI cell. The paths 1, 2 and 3 correspond to the ionic paths when the convective time is larger, equal, and smaller than the electrokinetic time, respectively.

Grahic Jump Location
Fig. 8

Steady tests at varying solution concentrations at a constant flow rate of 0.5 cm3·min−1

Grahic Jump Location
Fig. 9

Steady tests at varying flow rates at a constant solution concentration of 0.05 mg·cm−3

Grahic Jump Location
Fig. 10

Characteristic conductivity and adsorption efficiency for steady tests

Grahic Jump Location
Fig. 11

(a) Constant aerogel concentration model results for constant concentration steady tests, and (b) constant aerogel adsorption model results for constant concentration steady tests



Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related Journal Articles
Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In