0
Research Papers: Flows in Complex Systems

Pressure-Loss Coefficient of 90 deg Sharp-Angled Miter Elbows

[+] Author and Article Information
Wameedh T. M. Al-Tameemi

Department of Mechanical Engineering,
University of Sheffield,
Sheffield S1 4ET, UK;
Reconstruction and Projects Office,
Ministry of Higher Education and
Scientific Research,
Baghdad, Iraq
e-mail: wtal-tameemi1@sheffield.ac.uk

Pierre Ricco

Department of Mechanical Engineering,
University of Sheffield,
Sheffield S1 4ET, UK
e-mail: p.ricco@sheffield.ac.uk

Contributed by the Fluids Engineering Division of ASME for publication in the JOURNAL OF FLUIDS ENGINEERING. Manuscript received August 26, 2017; final manuscript received December 12, 2017; published online January 30, 2018. Assoc. Editor: Moran Wang.

J. Fluids Eng 140(6), 061102 (Jan 30, 2018) (7 pages) Paper No: FE-17-1534; doi: 10.1115/1.4038986 History: Received August 26, 2017; Revised December 12, 2017

The pressure drop across 90deg sharp-angled miter elbows connecting straight circular pipes is studied in a bespoke experimental facility by using water and air as working fluids flowing in the range of bulk Reynolds number 500<Re<60,000. To the best of our knowledge, the dependence on the Reynolds number of the pressure drop across the miter elbow scaled by the dynamic pressure, i.e., the pressure-loss coefficient K, is reported herein for the first time. The coefficient is shown to decrease sharply with the Reynolds number up to about Re=20,000 and, at higher Reynolds numbers, to approach mildly a constant K=0.9, which is about 20% lower than the currently reported value in the literature. We quantify this relation and the dependence between K and the straight-pipe friction factor at the same Reynolds number through two new empirical correlations, which will be useful for the design of piping systems fitted with these sharp elbows. The pressure drop is also expressed in terms of the scaled equivalent length, i.e., the length of a straight pipe that would produce the same pressure drop as the elbow at the same Reynolds number.

FIGURES IN THIS ARTICLE
<>
Copyright © 2018 by ASME
Your Session has timed out. Please sign back in to continue.

References

Dean, W. , 1927, “Note on the Motion of Fluid in a Curved Pipe,” London, Edinburgh, Dublin Philos. Mag. J. Sci., 4(20), pp. 208–223. [CrossRef]
Sugiyama, S. , Hayashi, T. , and Yamazaki, K. , 1983, “Flow Characteristics in the Curved Rectangular Channels: Visualization of Secondary Flow,” Bull. JSME, 26(216), pp. 964–969. [CrossRef]
Crawford, N. , Cunningham, G. , and Spedding, P. , 2003, “Prediction of Pressure Drop for Turbulent Fluid Flow in 90 Bends,” Proc. Inst. Mech. Eng., Part E, 217(3), pp. 153–155. [CrossRef]
Crawford, N. , Cunningham, G. , and Spence, S. , 2007, “An Experimental Investigation Into the Pressure Drop for Turbulent Flow in 90 Elbow Bends,” Proc. Inst. Mech. Eng., Part E, 221(2), pp. 77–88. [CrossRef]
Schmandt, B. , and Herwig, H. , 2012, “A Standard Method to Determine Loss Coefficients of Conduit Components Based on the Second Law of Thermodynamics,” ASME Paper No. ICNMM2012-73249.
Schmandt, B. , and Herwig, H. , 2013, “Loss Coefficients for Periodically Unsteady Flows in Conduit Components: Illustrated for Laminar Flow in a Circular Duct and a 90 Degree Bend,” ASME J. Fluids Eng., 135(3), p. 031204. [CrossRef]
Schmandt, B. , and Herwig, H. , 2016, “Losses Due to Conduit Components: An Optimization Strategy and Its Application,” ASME J. Fluids Eng., 138(3), p. 031204. [CrossRef]
Beij, K. , 1938, Pressure Losses for Fluid Flow in 90° Pipe Bends, Vol. 21, United States Department of Commerce, Washington, DC.
Ito, H. , 1960, “Pressure Losses in Smooth Pipe Bends,” ASME J. Fluids Eng., 82(1), pp. 131–140.
Kirchbach, H. , 1935, “Loss of Energy in Miter Bends,” Transactions of the Munich Hydraulic Institute, American Society of Mechanical Engineers, New York, Bulletin No. 3.
Schubart, W. , 1935, “Energy Loss in Smooth-and Rough-Surfaced Bends and Curves in Pipe Lines,” Trans. Hydraul. Inst. Munich Tech. Univ., 3, pp. 81–99.
Haidar, N. , 1995, “Prediction of Compressible Flow Pressure Losses in 30–150 Deg Sharp-Cornered Bends,” ASME J. Fluids Eng., 117(4), pp. 589–592. [CrossRef]
Moujaes, S. , and Aekula, S. , 2009, “CFD Predictions and Experimental Comparisons of Pressure Drop Effects of Turning Vanes in 90 Duct Elbows,” J. Energy Eng., 135(4), pp. 119–126. [CrossRef]
Munson, B. , Young, D. , and Okiishi, T. , 2006, Fundamentals of Fluid Mechanics, Wiley, Hoboken, NJ.
White, F. , 2011, Fluid Mechanics, 7th ed., McGraw-Hill, Boston, MA.
Rennels, D. , and Hudson, H. , 2012, Pipe Flow: A Practical and Comprehensive Guide, Wiley, Hoboken, NJ. [CrossRef]
Crane, 1988, Flow of Fluids Through Valves, Fittings, and Pipes, Crane, Newyork.
Spedding, P. , Benard, E. , and McNally, G. , 2004, “Fluid Flow Through 90 Degree Bends,” Dev. Chem. Eng. Miner. Process., 12(1–2), pp. 107–128.
Wilson, R. , McAdams, W. , and Seltzer, M. , 1922, “The Flow of Fluids Through Commercial Pipe Lines,” Ind. Eng. Chem., 14(2), pp. 105–119. [CrossRef]
Perry, J. , 1950, “Chemical Engineers' Handbook,” J. Chem. Educ., 27(9), p. 533. [CrossRef]
Lemmon, E. , Huber, M. , and McLinden, M. , 2010, “NIST Standard Reference Database 23: Reference Fluid Thermodynamic and Transport Properties—REFPROP. 9.0,” National Institute of Standards and Technology, Boulder, CO.
Taylor, J. R. , 1997, An Introduction to Error Analysis, University Science Books, Sausalito, CA.
Haaland, S. E. , 1983, “Simple and Explicit Formulas for the Friction Factor in Turbulent Pipe Flow,” ASME J. Fluids Eng., 105(1), pp. 89–90. [CrossRef]
McKeon, B. , Swanson, C. , Zagarola, M. V. , Donnelly, R. , and Smits, A. , 2004, “Friction Factors for Smooth Pipe Flow,” J. Fluid Mech., 511, pp. 41–44. [CrossRef]
den Toonder, J. , and Nieuwstadt, F. M. , 1997, “Reynolds Number Effects in a Turbulent Pipe Flow for Low to Moderate Re,” Phys. Fluids, 9(11), pp. 3398–3409. [CrossRef]
Swanson, C. , Julian, B. , Ihas, G. , and Donnelly, R. , 2002, “Pipe Flow Measurements Over a Wide Range of Reynolds Numbers Using Liquid Helium and Various Gases,” J. Fluid Mech., 461, pp. 51–60. [CrossRef]
Wu, X. , and Moin, P. , 2008, “A Direct Numerical Simulation Study on the Mean Velocity Characteristics in Turbulent Pipe Flow,” J. Fluid Mech., 608, pp. 81–112. [CrossRef]

Figures

Grahic Jump Location
Fig. 1

Schematic diagram of the experimental facility

Grahic Jump Location
Fig. 2

Schematic diagram of the 90 deg sharp-angled elbow and pressure tap

Grahic Jump Location
Fig. 3

Schematic diagram of the test sections

Grahic Jump Location
Fig. 4

Picture and schematic diagram of the pressure taps

Grahic Jump Location
Fig. 5

Friction factor Cf as a function of the Reynolds number Re for flow through straight pipes

Grahic Jump Location
Fig. 9

Pressure drop relative to the measurement location A along the 11-mm-diameter test section at Re=17,000 for air and water flows. The pressure-loss coefficient K and the scaled equivalent length L are indicated.

Grahic Jump Location
Fig. 8

Equivalent length to diameter ratio L for sharp-angled elbow as a function of Re. The symbols are given in Fig. 5.

Grahic Jump Location
Fig. 7

Pressure-loss coefficient K for sharp-angled elbows as a function of Cf

Grahic Jump Location
Fig. 6

Pressure-loss coefficient K for 90 deg sharp-angled elbows as a function of the Reynolds number Re. The symbols are given in Fig. 5.

Grahic Jump Location
Fig. 10

Air-flow pressure drop at different angles around the pipe periphery at stations C,D,E, and F of the 16-mm-diameter test section at different Reynolds numbers

Tables

Errata

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related Journal Articles
Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In