0

Newest Issue


Research Papers: Flows in Complex Systems

J. Fluids Eng. 2019;141(8):081101-081101-14. doi:10.1115/1.4042256.

An experimental and computational comparison of the turbulent flow field for a sharp 90 deg elbow and plugged tee junction is presented. These are commonly used industrial geometries with the tee often retrofitted by plugging the straight exit to create an elbow. Mean and fluctuating velocities along the midplane were measured via two-dimensional (2D) particle image velocimetry (PIV), and the results were compared with the predictions of Reynolds-averaged Navier–Stokes (RANS) simulations for Reynolds numbers of 11,500 and 115,000. Major flow features of the elbow and plugged tee were compared using the mean velocity contours. Geometry effects and Reynolds number effects were studied by examining the mean and root-mean-square (RMS) fluctuating velocity profiles at six positions. Finally, the asymmetry of the flow as measured by the position of the centroid of the volumetric flux and pressure loss data were examined to quantify the streamwise evolution of the flow in the respective geometries. It was found that in both geometries there was a large recirculation zone in the downstream leg but the RANS simulations predicted an overly long recirculation which led to significantly different mean and fluctuating velocities in that region when compared to the experiments. Comparison of velocity profiles showed that both experiments and numerics agree in the fact that the turbulence intensities were greater at higher Re downstream of the vertical leg. Finally, it was shown that the plugged tee recovered its symmetry more rapidly and created less pressure loss than the elbow.

Commentary by Dr. Valentin Fuster
J. Fluids Eng. 2019;141(8):081102-081102-12. doi:10.1115/1.4042257.

In industrial applications, cryogenic liquids are sometimes used as the working fluid of fluid machineries. In those fluids, the thermodynamic suppression effect of cavitation, which is normally ignored in water at room temperature, becomes obvious. When evaporation occurs in the cavitation region, the heat is supplied from the surrounding liquid. Hence, the liquid temperature is decreased, and cavitation is suppressed due to the decrease in saturated vapor pressure. Therefore, the performance of the fluid machinery can be improved. Computational fluid dynamics, which involves the use of a homogeneous model coupled with a thermal transport equation, is a powerful tool for the prediction of cavitation under thermodynamic effects. In this study, a thermodynamic model for a homogeneous model is introduced. In this model, the source term related to the latent heat of phase change appears explicitly, and the degree of heat transfer rate for evaporation and condensation can be adjusted separately to suit the homogeneous model. Our simplified thermodynamic model coupled with the Merkle cavitation model was validated for cryogenic cavitation on a two-dimensional (2D) quarter hydrofoil. The results obtained during the validation showed good agreement (in both pressure and temperature profiles) with the experimental data and were better than existing numerical results obtained by other researchers.

Commentary by Dr. Valentin Fuster
J. Fluids Eng. 2019;141(8):081103-081103-14. doi:10.1115/1.4042371.

In previous works, the authors presented computational fluid dynamics (CFD) results, which showed that injectors with noticeably steeper nozzle and needle tip angles 110 deg & 70 deg and 150 deg & 90 deg, respectively, attain higher efficiency than the industry standard, which, according to available literature on the public domain, ranges from 80 deg to 90 deg for nozzle and 50–60 deg for needle tip angles. Moreover, experimental testing of the entire Pelton system showed that gains of about 1% in efficiency can be achieved; however there appears to be an upper limit beyond which steeper designs are no longer optimal. This study aims at providing further insight by presenting additional CFD analysis of the runner, which has been coupled with the jet profile from the aforementioned injectors. The results are compared by examining the impact the jet shape has on the runner torque profile during the bucket cycle and the influence this has on turbine efficiency. It can be concluded that the secondary velocities, which contribute to the development of more significant free-surface degradations as the nozzle and needle tip angles are increased, result in a nonoptimal jet runner interaction.

Commentary by Dr. Valentin Fuster
J. Fluids Eng. 2019;141(8):081104-081104-13. doi:10.1115/1.4042372.

The impeller–volute tongue interaction strongly influences the aerodynamic performance of squirrel cage fan. To quantitatively evaluate the level of impeller–volute tongue interaction, we propose two parameters, i.e., recirculated flow coefficient and reversed flow coefficient based on a careful inspection of flow pattern near the volute tongue of a squirrel cage fan. Inspired by the good aerodynamic characteristics of owl wing, particular effort is made to develop a bionic design of volute tongue to improve the impeller–volute tongue match. The aerodynamic performances of both the squirrel cage fans with original volute tongue (OVT) and bionic volute tongue (BVT) are numerically and experimentally analyzed. The results show that, by employing the bionic design of volute tongue, the squirrel cage fan can achieve higher aerodynamic performance than that with OVT. Better match between impeller and volute tongue is obtained with smaller recirculated flow coefficient and reversed flow coefficient, validating the effectiveness of the proposed parameters to quantitatively evaluate the level of impeller–volute tongue interaction. In addition, the bionic design of volute tongue is beneficial for the improvement of flow quality and for the relief of abrupt pressure variation and axial nonuniformity of flow near the volute tongue. This work is helpful for a deep understanding of complex flow pattern in squirrel cage fan.

Commentary by Dr. Valentin Fuster
J. Fluids Eng. 2019;141(8):081105-081105-13. doi:10.1115/1.4042470.

The flow behavior through the vented channel of a brake disk determines its thermal performance, viz. its resistance to brake fade, brake wear, thermal distortion, and thermal cracking. We present experimental results of the flow characteristics inside the vented channel of a radial vane brake rotor with a selected number of vanes (i.e., 18, 36, and 72) but constant porosity (ε ∼ 0.8) at low rotational speeds (i.e., 25 rpm ≤ N ≤ 400 rpm). Using bulk flow and velocity field mapping measurement techniques, we observed that increasing the number of vanes for a given rotational speed results in (i) the increase in the mass flow rate of the air pumped by the rotor, (ii) the reduction of inflow angle (β) becoming more closely aligned with the vanes, (iii) more uniformly distributed passage velocity profiles, and (iv) increased Rossby number. In addition, for a certain range of rotational speeds (i.e., 100 rpm ≤ N ≤ 400 rpm), we identified the biased development of streamwise secondary flow structures in the vented passages that only form on the inboard side of the rotor. This is due to the entry conditions where the incoming flow must transition sharply from the axial to the radial direction as air is drawn into the rotating channel. The biased secondary flow is likely to cause uneven cooling of the brake rotor, leading to thermal distortion. At lower rotational speeds (i.e., N < 100 rpm), the biased secondary flows transitions into a symmetric structure.

Commentary by Dr. Valentin Fuster
J. Fluids Eng. 2019;141(8):081106-081106-10. doi:10.1115/1.4041892.

An experimental analysis of the start-up sequence of a bulb turbine was performed in a closed-loop circuit, and analyses of global performances were conducted under three start-up conditions. In order to conduct a deeper analysis of the runner behavior, a runner blade was equipped with 26 sensors, which were used to evaluate the transient pressure field using an interpolation method. By checking the global performances of all the conditions, the flow rate evolution follows the guide vane opening (GVO) evolution only for the two slowest GVO test cases. Additionally, the use of defined dimensionless numbers allowed for some degree of universal evolution to be revealed, and for the peak of torque to be characterized. The pressure on the runner blades was also investigated. Although the runner operates like an impulse turbine at the beginning of the start-up sequence, its blades act like more airfoils when the torque reaches its peak. Moreover, the fluctuations at the end of the start/up sequence suggest that the stress on the blade could be more important than the stress observed on the driven shaft. Furthermore, local phenomena, such as suction on the pressure side of the runner blade near the shroud, were also observed on the pressure distribution, which is incongruent with the theoretical inlet velocity field estimated from global performances. These observations suggest the presence of a backflow and a cavitation pocket. Moreover, a flow instability probably occurs at low GVO speed and produces some torque fluctuations around the maximum torque value.

Commentary by Dr. Valentin Fuster
J. Fluids Eng. 2019;141(8):081107-081107-6. doi:10.1115/1.4042558.

Unsteady laminar nonlinear slip flow of power law fluids in a microchannel is investigated. The nonlinear partial differential equation resulting from the momentum balance is solved with linear as well as nonlinear boundary conditions at the channel wall. We prove the existence of the weak solution, develop a semi-analytical solution based on the pseudo-spectral-Galerkin and Tau methods, and discuss the influence and effect of the slip coefficient and power law index on the time-dependent velocity profiles. Larger slip at the wall generates increased velocity profiles, and this effect is further enhanced by increasing the power law index. Comparatively, the velocity of the Newtonian fluid is larger and smaller than that of the power law fluid for the same value of the slippage coefficient if the power index is smaller and larger, respectively, than one.

Commentary by Dr. Valentin Fuster

Research Papers: Fundamental Issues and Canonical Flows

J. Fluids Eng. 2019;141(8):081201-081201-10. doi:10.1115/1.4042469.

Mixing in a microfluidic device is a major challenge due to creeping flow, which is a significant roadblock for development of lab-on-a-chip device. In this study, an analytical model is presented to study the fluid flow behavior in a microfluidic mixer using time-periodic electro-osmotic flow. To facilitate mixing through microvortices, nonuniform surface charge condition is considered. A generalized analytical solution is obtained for the time-periodic electro-osmotic flow using a stream function technique. The electro-osmotic body force term is accounted as a slip boundary condition on the channel wall, which is a function of time and space. To demonstrate the applicability of the analytical model, two different surface conditions are considered: sinusoidal and step change in zeta potential along the channel surface. Depending on the zeta potential distribution, we obtained diverse flow patterns and vortices. The flow circulation and its structures depend on channel size, charge distribution, and the applied electric field frequency. Our results indicate that the sinusoidal zeta potential distribution provides elliptical shaped vortices, whereas the step change zeta potential provides rectangular shaped vortices. This analytical model is expected to aid in the effective micromixer design.

Commentary by Dr. Valentin Fuster
J. Fluids Eng. 2019;141(8):081202-081202-10. doi:10.1115/1.4042376.

The choked mass flux density and the choked momentum flux density for the nonideal fluids methane and nitrogen have been calculated using the Soave–Redlich–Kwong equation of state (EoS). For the computation a steady, one-dimensional (1D), isenthalpic and isentropic flow is assumed. The developed algorithm for the calculation of the choked flow properties includes a bounded multidimensional Newton method. A possible second phase emerging in the critical nozzle area is excluded using the saturation properties of the considered fluids. The critical ratios of pressure, density, temperature, and speed of sound are discussed and compared to other publications. Formulations of the choked mass flux density and the choked momentum flux density explicit in Tr, pr, and Zr are given valid for different reduced pressures and temperatures depending on the fluid. Additional computational fluid dynamics (CFD) simulations are carried out in order to validate the findings of the algorithm and the proposed correlations.

Commentary by Dr. Valentin Fuster
J. Fluids Eng. 2019;141(8):081203-081203-12. doi:10.1115/1.4042560.

The mitigation of the precessing vortex core developing in the draft tube of Francis turbines operating under part load conditions is crucial to increase the operation flexibility of these hydraulic machines to balance the massive power production of intermittent energy sources. A systematic approach following the optimal control theory is, therefore, presented to control this vortical flow structure. Modal analysis characterizes the part load vortex rope as a self-sustained instability associated with an unstable eigenmode. Based on this physical characteristic, an objective function targeting a zero value of the unstable eigenvalue growth rate is defined and subsequently minimized using an adjoint-based optimization algorithm. We determine an optimal force distribution that successfully quenches the part load vortex rope and sketches the design of a realistic control appendage.

Commentary by Dr. Valentin Fuster

Research Papers: Multiphase Flows

J. Fluids Eng. 2019;141(8):081301-081301-9. doi:10.1115/1.4042557.

The key to effective magnetic drug targeting (MDT) is to improve the aggregation of magnetic drug carrier particles (MDCPs) at the target site. Compared to related theoretical models, the novelty of this investigation is mainly reflected in that the microvascular blood is considered as a two-phase fluid composed of a continuous phase (plasma) and a discrete phase (red blood cells (RBCs)). And plasma flow state is quantitatively described based on the Navier–Stokes equation of two-phase flow theory, the effect of momentum exchange between the two-phase interface is considered in the Navier–Stokes equation. Besides, the coupling effect between plasma pressure and tissue fluid pressure is considered. The random motion effects and the collision effects of MDCPs transported in the blood are quantitatively described using the Boltzmann equation. The results show that the capture efficiency (CE) presents a nonlinear increase with the increase of magnetic induction intensity and a nonlinear decrease with the increase of plasma velocity, but an approximately linear increase with the increase of the particle radius. Furthermore, greater permeability of the microvessel wall promotes the aggregation of MDCPs. The CE predicted by the model agrees well with the experimental results.

Commentary by Dr. Valentin Fuster

Research Papers: Techniques and Procedures

J. Fluids Eng. 2019;141(8):081401-081401-8. doi:10.1115/1.4042373.

Inlet conditions for a turbulent jet are known to affect the near field behavior but eventually lose their significance downstream. Metrics of importance are often derived from mean and fluctuating velocity components, but little has been done to explore inlet effects on transport of a scalar quantity (e.g., temperature). This paper aims to provide fundamental understanding in this regard and employs large eddy simulations (LES) of a nonisothermal round turbulent jet (Reynolds number of 16,000) with geometry and boundary conditions mimicked after a well-known experimental study. The jet inlet is first modeled with a standard Blasius profile and next by performing a simulation of the upstream flow modeled with either detached eddy simulations (DES) or LES for the second and third approaches, respectively. Only the model employing LES for both upstream nozzle and downstream jet is found to completely capture the root-mean-square (RMS) temperature behavior, namely, a distinct hump when normalized by the local mean centerline temperature at roughly five diameters downstream. Regarding the far field conditions, all three inlet conditions converge for the centerline values, but the radial distributions still portray non-negligible differences. Not surprisingly, the complete LES modeling approach agrees the best with experimental data for mean and RMS distributions, suggesting that the inlet condition plays a vital role in both the near and far field of the jet. The current effort is the very first LES study to successfully capture flow physics for a nonisothermal round turbulent jet in near and far field locations.

Commentary by Dr. Valentin Fuster

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In