The expansive growth and differentiation potential of human embryonic stem cells (hESCs) make them a promising source of cells for regenerative medicine. However, this promise is off set by the propensity for spontaneous or uncontrolled differentiation to result in heterogeneous cell populations. Cell elasticity has recently been shown to characterize particular cell phenotypes, with undifferentiated and differentiated cells sometimes showing significant differences in their elasticities. In this study, we determined the Young’s modulus of hESCs by atomic force microscopy using a pyramidal tip. Using this method we are able to take point measurements of elasticity at multiple locations on a single cell, allowing local variations due to cell structure to be identified. We found considerable differences in the elasticity of the analyzed hESCs, reflected by a broad range of Young’s modulus (0.05-10 kPa). This surprisingly high variation suggests that elasticity could serve as the basis of a simple and efficient large scale purification/separation technique to discriminate subpopulations of hESCs.
Skip Nav Destination
Article navigation
October 2011
Research Papers
Elasticity of Human Embryonic Stem Cells as Determined by Atomic Force Microscopy
Robert Kiss,
Robert Kiss
Chemical Engineering, School of Engineering and Physical Sciences,
Heriot-Watt University
, Edinburgh EH14 4AS, U.K
.
Search for other works by this author on:
Henry Bock,
Henry Bock
Chemical Engineering, School of Engineering and Physical Sciences,
Heriot-Watt University
, Edinburgh EH14 4AS, U.K
.
Search for other works by this author on:
Steve Pells,
Steve Pells
MRC Centre for Regenerative Medicine, College of Medicine and Veterinary Medicine,
Edinburgh University
, Edinburgh EH16 4SB, U.K
.
Search for other works by this author on:
Elisabetta Canetta,
Elisabetta Canetta
BIONTHE (Bio- and Nano-Technologies for Health and Environment) Center, Division of Biotechnology and Forensic Sciences, School of Contemporary Sciences,
University of Abertay Dundee
, Dundee DD1 1HG, U.K
.
Search for other works by this author on:
Ashok K. Adya,
Ashok K. Adya
BIONTHE (Bio- and Nano-Technologies for Health and Environment) Center, Division of Biotechnology and Forensic Sciences, School of Contemporary Sciences,
University of Abertay Dundee
, Dundee DD1 1HG, U.K
.
Search for other works by this author on:
Andrew J. Moore,
Andrew J. Moore
Mechanical Engineering, School of Engineering and Physical Sciences,
Heriot-Watt University
, Edinburgh EH14 4AS, U.K
.
Search for other works by this author on:
Paul De Sousa,
Paul De Sousa
MRC Centre for Regenerative Medicine, College of Medicine and Veterinary Medicine,
Edinburgh University
, Edinburgh EH16 4SB, U.K
.
Search for other works by this author on:
Nicholas A. Willoughby
Nicholas A. Willoughby
Chemical Engineering, School of Engineering and Physical Sciences,
Heriot-Watt University
, Edinburgh EH14 4AS, U.K
.
Search for other works by this author on:
Robert Kiss
Chemical Engineering, School of Engineering and Physical Sciences,
Heriot-Watt University
, Edinburgh EH14 4AS, U.K
.
Henry Bock
Chemical Engineering, School of Engineering and Physical Sciences,
Heriot-Watt University
, Edinburgh EH14 4AS, U.K
.
Steve Pells
MRC Centre for Regenerative Medicine, College of Medicine and Veterinary Medicine,
Edinburgh University
, Edinburgh EH16 4SB, U.K
.
Elisabetta Canetta
BIONTHE (Bio- and Nano-Technologies for Health and Environment) Center, Division of Biotechnology and Forensic Sciences, School of Contemporary Sciences,
University of Abertay Dundee
, Dundee DD1 1HG, U.K
.
Ashok K. Adya
BIONTHE (Bio- and Nano-Technologies for Health and Environment) Center, Division of Biotechnology and Forensic Sciences, School of Contemporary Sciences,
University of Abertay Dundee
, Dundee DD1 1HG, U.K
.
Andrew J. Moore
Mechanical Engineering, School of Engineering and Physical Sciences,
Heriot-Watt University
, Edinburgh EH14 4AS, U.K
.
Paul De Sousa
MRC Centre for Regenerative Medicine, College of Medicine and Veterinary Medicine,
Edinburgh University
, Edinburgh EH16 4SB, U.K
.
Nicholas A. Willoughby
Chemical Engineering, School of Engineering and Physical Sciences,
Heriot-Watt University
, Edinburgh EH14 4AS, U.K
.J Biomech Eng. Oct 2011, 133(10): 101009 (9 pages)
Published Online: November 7, 2011
Article history
Received:
December 3, 2010
Accepted:
August 22, 2011
Online:
November 7, 2011
Published:
November 7, 2011
Citation
Kiss, R., Bock, H., Pells, S., Canetta, E., Adya, A. K., Moore, A. J., De Sousa, P., and Willoughby, N. A. (November 7, 2011). "Elasticity of Human Embryonic Stem Cells as Determined by Atomic Force Microscopy." ASME. J Biomech Eng. October 2011; 133(10): 101009. https://doi.org/10.1115/1.4005286
Download citation file:
Get Email Alerts
Simulating the Growth of TATA-Box Binding Protein-Associated Factor 15 Inclusions in Neuron Soma
J Biomech Eng (December 2024)
Effect of Structure and Wearing Modes on the Protective Performance of Industrial Safety Helmet
J Biomech Eng (December 2024)
Sex-Based Differences and Asymmetry in Hip Kinematics During Unilateral Extension From Deep Hip Flexion
J Biomech Eng (December 2024)
Related Articles
Robust Strategies for Automated AFM Force Curve Analysis—I. Non-adhesive Indentation of Soft, Inhomogeneous Materials
J Biomech Eng (June,2007)
Robust Strategies for Automated AFM Force Curve Analysis—II: Adhesion-Influenced Indentation of Soft, Elastic Materials
J Biomech Eng (December,2007)
Arterial Stiffness: Different Metrics, Different Meanings
J Biomech Eng (September,2019)
Cholesterol-Dependent Modulation of Stem Cell Biomechanics: Application to Adipogenesis
J Biomech Eng (August,2019)
Related Proceedings Papers
Related Chapters
A Dynamic Path Planning Algorithm with Application to AFM Tip Steering
International Conference on Advanced Computer Theory and Engineering (ICACTE 2009)
Processing/Structure/Properties Relationships in Polymer Blends for the Development of Functional Polymer Foams
Advances in Multidisciplinary Engineering
Applications
Introduction to Finite Element, Boundary Element, and Meshless Methods: With Applications to Heat Transfer and Fluid Flow