This paper presents the reliability of anisotropic conductive film (ACF) joint tested under reflow soldering and environmental test effect. The ACF joint behaved differently under different reflow soldering profiles. The lower reflow temperature resulted in more reliable ACF joints by maintaining low contact resistance. By contrast, high contact resistance was found in assemblies treated with higher reflow. Under humidity aging (85°C/85%RH), bumpless chips proved to be unreliable due to corrosion mechanism. Moreover, ACF had shown degradation in chemical and physical properties, including modulus reduction, Tg depression, polymer hydrolysis, and surface swelling after exposing to humidity aging. The deterioration in reliability of aged ACF joint during reflow process was mainly caused by hydroscopic swelling-induced stress of ACF.

1.
Persson, K., Lai, Z., Zribi, A., Liu, J., and Willander, M., 1998, “Effect of Bump Height on Flip Chip Joint Reliability Using ACA,” Proceedings of 3rd International Conference on Adhesive Joining and Coating Technology In Electronic Manufacturing, Binghamton, New York, September, pp. 132–136.
2.
Kumano
,
Y.
,
Tomura
,
Y.
,
Itagaki
,
M.
, and
Bessho
,
Y.
,
2001
, “
Development of Chip on Flex Using SBB Flip-Chip Technology
,”
Microelectron. Reliab.
,
41
(
4
), pp.
525
530
.
3.
Jokien
,
E.
, and
Ristolainen
,
E.
,
2002
, “
Anisotropic Conductive Film Flip Chip Joining Using Thin Chips
,”
Microelectron. Reliab.
,
42
(
12
), pp.
1913
1920
.
4.
Yin
,
C. Y.
,
Alam
,
M. O.
,
Chan
,
Y. C.
,
Bailey
,
C.
, and
Lu
,
H.
,
2003
, “
The Effect of Reflow Process on the Contact Resistance and Reliability of Anisotropic Conductive Film Interconnection for Flip Chip on Flex Applications
,”
Microelectron. Reliab.
,
43
(
4
), pp.
625
633
.
5.
Harrison
,
M. R.
,
Vincent
,
J. H.
, and
Steen
,
H. A.
,
2001
, “
Lead-Free Reflow Soldering for Electronics Assembly
,”
Soldering and Surface Mount Technology
,
13
(
3
), pp.
21
38
.
6.
Seppala
,
A.
,
Aalto
,
K.
, and
Ristolainen
,
E.
,
2003
, “
Reducing Bonding Cycle Time of Adhesive Flip Chip Process
,”
Soldering and Surface Mount Technology
,
15
(
1
), pp.
16
20
.
7.
Lyons
,
A. M.
,
Hall
,
E.
,
Wong
,
Y. H.
, and
Adams
,
G.
,
1996
, “
A New Approach to Using Anisotropically Conductive Adhesives for Flip-Chip Assembly
,”
IEEE Trans. Compon. Packag. Manuf. Technol.
,
19
(
1
), pp.
5
11
.
8.
Yim, M. J., Paik, K.-W., Kim, T. S., and Yang, K. K., 1998, “Anisotropic Conductive Film (ACF) Interconnection for Display Packaging Applications,” Electronic Components and Technology Conference, Seattle, May, pp. 1036–1041.
9.
Connell, G., Zenner, R. L. D., and Gerber, J. A., 1997, “Conductive Adhesive Flip-Chip Bonding for Bumped and Unbumped Die,” Electronic Components and Technology Conference, San Jose, May, pp. 274–278.
10.
Lin, C. W. C., Chiang, C. L., and Yang, T. K., 2002, “Bumpless Flip Chip Packages,” International Symposium on Electronic Materials and Packaging, Kaohsiung, December, pp. 173–177.
11.
Sea, T. K., Tan, T. C., and Peh, E. K., 1997, “Reflowable Anisotropic Conductive Adhesives for Flipchip Packaging,” IEEE/CPMT Electronic Packaging Technology Conference, Singapore, October, pp. 259–262.
12.
Liu
,
J.
,
2000
, “
ACA Bonding Technology for Low Cost Electronics Packaging Applications-Current Status and Remaining Challenges
,”
Soldering and Surface Mount Technology
,
13
(
3
), pp.
39
57
.
13.
Li, Y., Gao, B., and Unsworth, J., 1994, “Degradation of Epoxy Insulation Under Combined High Humidity and Elevated Temperature,” Proceedings of the 4th International Conference on Properties and Applications of Dielectric Materials, Brisbane, July, pp. 752–755.
14.
Kotaka, K., Abe, Y., and Homma, Y., 1998, “The New Underfill Material With High Adhesion Strength for Flip-Chip Applications,” IEMT/IMC Proceedings, Austin, October, pp. 369–373.
15.
Chiu
,
Y. W.
,
Chan
,
Y. C.
, and
Lui
,
S. M.
,
2002
, “
Study of Short-Circuiting Between Adjacent Joints Under Electric Field Effects in Fine Pitch Anisotropic Conductive Adhesive Interconnects
,”
Microelectron. Reliab.
,
42
(
12
), pp.
1945
1951
.
16.
Liu, J., Lai, Z., Kristiansen, H., and Khoo, C., 1998, “Overview of Conductive Adhesive Joining Technology in Electronics Package Applications,” Proceedings of 3rd International Conference on Adhesive Joining and Coating Technology in Electronic Manufacturing, Binghamton, New York, September, pp. 1–18.
17.
Sugiura
,
M.
,
Mitsuoka
,
T.
,
Murase
,
A.
, and
Ueda
,
K.
,
2000
, “
Distribution Analysis of Hydroxyl Groups in Polymers by Derivatization-Electron Probe X-Ray Microanalysis
,”
Anal. Sci.
,
16
, pp.
1313
1316
.
18.
Luo, S., Leisen, J., and Wong, C. P., 2001, “Study on Mobility of Water and Polymer Chain in Epoxy for Microelectronic Applications,” Electronic Components and Technology Conference, Orlando, May, pp. 149–154.
19.
Park
,
C. E.
,
Han
,
B. J.
, and
Bair
,
H. E.
,
1997
, “
Humidity Effects on the Adhesion Strength Between Solder Ball and Epoxy Underfills
,”
Polymer
,
38
(
15
), pp.
3811
3818
.
20.
Luo, S., and Wong, C. P., 2001, “Influence of Temperature and Humidity on Adhesion of Underfill for Flip Chip Packaging,” Electronic Components and Technology Conference, Orlando, May, pp. 155–162.
21.
MieBner, R., Aschenbrenner, R., and Reichl, H., 1998, “Correlation of Thermo-Mechanical Properties of Adhesives With Reliability of FC Interconnections,” Proceedings of 3rd International Conference on Adhesive Joining and Coating Technology in Electronics Manufacturing, Binghamton, New York, September, pp. 299–304.
22.
Lai
,
Z.
,
Lar
,
R. Y.
,
Persson
,
K.
, and
Liu
,
J.
,
1998
, “
Effect of Bump Height on the Reliability of ACA Flip-Chip Joining With FR4 Rigid and Polyimide Flexible Substrate
,”
J. Electron. Manufact.
,
8
(
3
,4), pp.
217
224
.
23.
Ogunjimi, A. O., Whalley, D. C., and Williams, D. J., 1993, “Thermal Stress Analysis of Conductive Adhesive Joints,” Japan International Electronics Manufacturing Technology Symposium, Kanazawa, June, pp. 349–353.
24.
Petch
,
M.
,
1990
, “
A Model for Moisture Induced Corrosion Failures in Microelectronic Packages
,”
IEEE Trans. Compon., Hybrids, and Manuf. Technol.
,
13
(
2
), pp.
383
389
.
25.
Zhang
,
J. H.
,
Chan
,
Y. C.
,
Alam
,
M. O.
, and
Fu
,
S.
,
2003
, “
Contact Resistance and Adhesion Performance of ACF Connections to Aluminum Metallization
,”
Microelectron. Reliab.
,
43
(
8
), pp.
1303
1310
.
26.
Wong, E. H., Chan, K. C., Rajoo, R., and Lim, T. B., 2000, “The Mechanics and Impact of Hygroscopic Swelling of Polymeric Materials in Electronic Packaging,” Electronic Components and Technology Conference, Las Vegas, May, pp. 576–580.
27.
Chiang
,
Y. M.
, and
Marta
,
F. G.
,
2003
, “
Relation of Swelling and Tg Depression to the Apparent Free Volume of a Particle-Filled, Epoxy-Based Adhesive
,”
J. Appl. Polym. Sci.
,
87
, pp.
1436
1444
.
You do not currently have access to this content.