The semiconductor community is developing three-dimensional circuits that integrate logic, memory, optoelectronic and radio-frequency devices, and microelectromechanical systems. These three-dimensional (3D) circuits pose important challenges for thermal management due to the increasing heat load per unit surface area. This paper theoretically studies 3D circuit cooling by means of an integrated microchannel network. Predictions are based on thermal models solving one-dimensional conservation equations for boiling convection along microchannels, and are consistent with past data obtained from straight channels. The model is combined within a thermal resistance network to predict temperature distributions in logic and memory. The calculations indicate that a layer of integrated microchannel cooling can remove heat densities up to within a 3D architecture with a maximum circuit temperature of The cooling strategy described in this paper will enable 3D circuits to include greater numbers of active levels while exposing external surface area for functional signal transmission.
Skip Nav Destination
e-mail: jaemokoo@stanford.edu
Article navigation
Article
Integrated Microchannel Cooling for Three-Dimensional Electronic Circuit Architectures
Jae-Mo Koo,
e-mail: jaemokoo@stanford.edu
Jae-Mo Koo
Mechanical Engineering Department, Stanford University, Stanford, CA 94305
Search for other works by this author on:
Sungjun Im,
Sungjun Im
Materials Science and Engineering Department, Stanford University, Stanford, CA 94305
Search for other works by this author on:
Linan Jiang,
Linan Jiang
Mechanical Engineering Department, Stanford University, Stanford, CA 94305
Search for other works by this author on:
Kenneth E. Goodson
Kenneth E. Goodson
Mechanical Engineering Department, Stanford University, Stanford, CA 94305
Search for other works by this author on:
Jae-Mo Koo
Mechanical Engineering Department, Stanford University, Stanford, CA 94305
e-mail: jaemokoo@stanford.edu
Sungjun Im
Materials Science and Engineering Department, Stanford University, Stanford, CA 94305
Linan Jiang
Mechanical Engineering Department, Stanford University, Stanford, CA 94305
Kenneth E. Goodson
Mechanical Engineering Department, Stanford University, Stanford, CA 94305
Contributed by the Heat Transfer Division for publication in the JOURNAL OF HEAT TRANSFER. Manuscript received April 23, 2004; revision received September 11, 2004. Associate Editor: C. Amon.
J. Heat Transfer. Jan 2005, 127(1): 49-58 (10 pages)
Published Online: February 15, 2005
Article history
Received:
April 23, 2004
Revised:
September 11, 2004
Online:
February 15, 2005
Citation
Koo, J., Im, S., Jiang , L., and Goodson, K. E. (February 15, 2005). "Integrated Microchannel Cooling for Three-Dimensional Electronic Circuit Architectures ." ASME. J. Heat Transfer. January 2005; 127(1): 49–58. https://doi.org/10.1115/1.1839582
Download citation file:
Get Email Alerts
Cited By
Entropic Analysis of the Maximum Output Power of Thermoradiative Cells
J. Heat Mass Transfer
Molecular Dynamics Simulations in Nanoscale Heat Transfer: A Mini Review
J. Heat Mass Transfer
Related Articles
Fluid Flow and Thermal Characteristics of a Microchannel Heat Sink Subject to an Impinging Air Jet
J. Heat Transfer (July,2005)
Stacked Microchannel Heat Sinks for Liquid Cooling of Microelectronic Components
J. Electron. Packag (March,2004)
Forced Convection in Microstructures for Electronic Equipment Cooling
J. Heat Transfer (August,1999)
Experimental Investigation of an Ultrathin Manifold Microchannel Heat Sink for Liquid-Cooled Chips
J. Heat Transfer (August,2010)
Related Proceedings Papers
Related Chapters
Even a Watched Pot Boils Eventually
Hot Air Rises and Heat Sinks: Everything You Know about Cooling Electronics Is Wrong
Thermal Design Guide of Liquid Cooled Systems
Thermal Design of Liquid Cooled Microelectronic Equipment
Resistance Mythology
Hot Air Rises and Heat Sinks: Everything You Know about Cooling Electronics Is Wrong