The present study reports a unique tensile response of pure aluminum triggered due to the presence of SiC particles at nanolength scale. Al/SiC nanocomposites were synthesized by using energy efficient microwave assisted powder metallurgy route. Characterization studies conducted on the extruded samples revealed that the increasing presence of SiC particles at nanolength scale did not affect the 0.2% yield strength but increased ultimate tensile strength and work of fracture. Most interestingly, the presence of SiC nanoparticles increased the uniform, nonuniform, and total strain of aluminum when compared with pure aluminum. An attempt has been made in this study to inter-relate the enhanced tensile response of aluminum with the ability of SiC nanoparticles to homogenize the slip process and to delay void initiation and coalescence during tensile loading.
Skip Nav Destination
Article navigation
October 2010
Research Papers
Enhancing Uniform, Nonuniform, and Total Failure Strain of Aluminum by Using SiC at Nanolength Scale
Sanjay Kumar Thakur,
Sanjay Kumar Thakur
Delphi Automotive Systems Singapore Pte Ltd.
, 501 Ang Mo Kio Industrial Park 1, Singapore 569621, Singapore
Search for other works by this author on:
Khin Sandar Tun,
Khin Sandar Tun
Department of Mechanical Engineering,
National University of Singapore
, Singapore 117576, Singapore
Search for other works by this author on:
Manoj Gupta
Manoj Gupta
Department of Mechanical Engineering,
National University of Singapore
, Singapore 117576, Singapore
Search for other works by this author on:
Sanjay Kumar Thakur
Delphi Automotive Systems Singapore Pte Ltd.
, 501 Ang Mo Kio Industrial Park 1, Singapore 569621, Singapore
Khin Sandar Tun
Department of Mechanical Engineering,
National University of Singapore
, Singapore 117576, Singapore
Manoj Gupta
Department of Mechanical Engineering,
National University of Singapore
, Singapore 117576, SingaporeJ. Eng. Mater. Technol. Oct 2010, 132(4): 041002 (6 pages)
Published Online: September 8, 2010
Article history
Received:
April 6, 2010
Revised:
June 16, 2010
Online:
September 8, 2010
Published:
September 8, 2010
Citation
Thakur, S. K., Tun, K. S., and Gupta, M. (September 8, 2010). "Enhancing Uniform, Nonuniform, and Total Failure Strain of Aluminum by Using SiC at Nanolength Scale." ASME. J. Eng. Mater. Technol. October 2010; 132(4): 041002. https://doi.org/10.1115/1.4002150
Download citation file:
Get Email Alerts
Modeling Growth and Viscous Flow of Oxide on Cylindrical Silicon Surfaces Including Piezoviscous Inhibition
J. Eng. Mater. Technol (April 2025)
Thermal Conductivity of 3D-Printed Metal Using Extrusion-Based Metal Additive Manufacturing Process
J. Eng. Mater. Technol (April 2025)
Related Articles
Development and Characterization of Ductile Mg ∕ Y 2 O 3 Nanocomposites
J. Eng. Mater. Technol (July,2007)
Microwave Synthesis and Characterization of Magnesium Based Composites Containing Nanosized SiC and Hybrid ( Si C + Al 2 O 3 ) Reinforcements
J. Eng. Mater. Technol (April,2007)
Mechanical Properties and Microstructure of Mg ∕ Si C Nanocomposites Fabricated by Ultrasonic Cavitation Based Nanomanufacturing
J. Manuf. Sci. Eng (June,2008)
Polycarbonate and a Polycarbonate-POSS Nanocomposite at High Rates of
Deformation
J. Eng. Mater. Technol (October,2006)
Related Proceedings Papers
Related Chapters
Introduction and Definitions
Handbook on Stiffness & Damping in Mechanical Design
Compromise between Tensile and Fatigue Strength
New Advanced High Strength Steels: Optimizing Properties
Section III: Subsections NC and ND — Class 2 and 3 Components
Companion Guide to the ASME Boiler and Pressure Vessel Code, Volume 1, Fourth Edition