An innovative manufacturing method, bladder assisted composite manufacturing (BACM), to fabricate geometrically complex, hollow parts made of polymeric composite materials is presented. Unlike the conventional bladder or diaphragm assisted curing processes, BACM uses an internally heated bladder to provide the consolidation pressure at the required cure temperature. The feasibility of this manufacturing method is demonstrated by fabricating laminated composite cylinders using multiple cure pressures and number of plies. The elastic moduli, failure strength, fiber volume fraction, and void contents of the cylinders were found to be comparable to the values obtained from flat laminates produced by hot plate molding of the same material. Compared to conventional bladder manufacturing methods, the BACM process reduced the energy required to cure the cylinders by almost 50% due to internal heating and insulated mold.
Issue Section:
Technical Briefs
References
1.
Lehmann
, U.
, and Michaeli
, W.
, 1998
, “Cores Lead to an Automated Production of Hollow Composite Parts in Resin Transfer Moulding
,” Composites, Part A
, 29A
, pp. 803
–810
.10.1016/S1359-835X(98)00007-42.
Ghiasi
, H.
, Lessard
, L.
, Pasini
, D.
, and Thouin
, M.
, 2010
, “Optimum Structural and Manufacturing Design of a Braided Hollow Composite Part
,” Appl. Compos. Mater.
, 17
(2
), pp. 159
–173
.10.1007/s10443-009-9106-63.
Salomi
, A.
, Greco
, A.
, Felline
, F.
, Manni
, O.
, and Maffezzoli
, A.
, 2007
, “A Preliminary Study on Bladder-Assisted Rotomolding of Thermoplastic Polymer Composites
,” Adv. Polym. Technol.
, 26
(1
), pp. 21
–32
.10.1002/adv.200854.
Visconti
, I. C.
, and Langella
, A.
, 1992
, “Analytical Modelling of Pressure Bag Technology
,” Compos. Manuf.
, 3
(1
), pp. 3
–6
.10.1016/0956-7143(92)90176-U5.
Trimble
, B. J.
, 1992
, “Method of Making Composite Cycle Frame Components
,” U.S. Patent No. 5,158,733.6.
Rebard
, D.
, 2004
, “Bladder Molding With Latex in the Recreational Industry Lessons Learned
,” Proceeding of 49th International SAMPE Symposium and Exhibition
, SAMPE, Long Beach, CA
, pp. 79
–82
.7.
McCarthy
, R. F. J.
, Haines
, G. H.
, and Newley
, R. A.
, 1994
, “Polymer Composite Applications to Aerospace Equipment
,” Compos. Manuf.
, 5
(2
), pp. 83
–93
.10.1016/0956-7143(94)90059-08.
Bader
, M. G.
, 2002
, “Selection of Composite Materials and Manufacturing Routes for Cost-Effective Performance
,” Composites, Part A
, 33
, pp. 913
–934
.10.1016/S1359-835X(02)00044-19.
Hodgkin
, H. H.
, and Rabu
, N.
, 2000
, “A New Development in High-Speed Composite Fabrication for Aerospace, Automotive, and Marine Applications
,” Proceedings of 45th International SAMPE Symposium and Exhibition
, SAMPE, Long Beach, CA
, pp. 2274
–2282
.10.
Tomblin
, J. S.
, McKenna
, J.
, Ng
, Y. C.
, and Raju
, K. S.
, 2001
, “B-Basis Design Allowables for Epoxy-Based Prepreg Newport E-Glass Fabric 7781/NB-321
,” AGATE-WP3.3-033051-097, NASA
, Washington, DC
.11.
Raju
, K. S.
, Dandayudhapani
, S.
, and Thorbole
, C. K.
, 2008
, “Characterization of In-Plane Shear Properties of Laminated Composites at Medium Strain Rates
,” J. Aircr.
, 45
(2
), pp. 493
–497
.10.2514/1.3002612.
Karni
, J.
, and Karni
, E. Y.
, 1995
, “Gypsum in Construction: Origin and Properties
,” Mater. Struct.
, 28
, pp. 92
–100
.10.1007/BF0247317613.
Gupta
, N. K.
, and Abbas
, H.
, 2000
, “Lateral Collapse of Composite Cylindrical Tubes Between Flat Platens
,” Int. J. Impact Eng.
, 24
, pp. 329
–345
.10.1016/S0734-743X(99)00173-614.
Prosen
, S. P.
, Karpe
, S.
, Kinna
, M. A.
, Mueller
, C.
, Perry
, H. A.
, and Barnet
, F. R.
, 1963
, “Compression, Fatigue, and Stress Studies on NOL Ring Specimens
,” Symposium for Filament Wound Reinforced Plastics, ASTM International
, Naval Ordnance Laboratory White Oak, Silver Spring, MD
, pp. 105
–122
.15.
Guedes
, R. M.
, and Sa'
, A.
, 2008
, “Numerical Analysis of Singly Curved Shallow Composite Panels Under Three-Point Bend Load
,” Compos. Struct.
, 83
, pp. 212
–220
.10.1016/j.compstruct.2007.04.00516.
Hamidi
, Y. K.
, Aktas
, L.
, and Altan
, M. C.
, 2005
, “Effect of Packing on Void Morphology in Resin Transfer Molded E-Glass/Epoxy Composites
,” Polym. Compos.
, 26
(5
), pp. 614
–627
.10.1002/pc.2013217.
Kardos
, J. L.
, Dave
, R.
, and Dudukovic
, M. P.
, 1988
, “Voids in Composites
,” Manufacturing Science of Composites
, T. G.
Gutowski
, ed., ASME
, Atlanta, GA
, pp. 41
–48
.18.
Browning
, C. E.
, 1986
, “Processing Science of Graphite/Epoxy Composites
,” Chem. Eng. Prog.
, 82
(6
), pp. 41
–44
.19.
Liu
, L.
, Zhang
, B.-M.
, Wang
, D.-F.
, and Wu
, Z.-J.
, 2006
, “Effects of Cure Cycles on Void Content and Mechanical Properties of Composite Laminates
,” Compos. Struct.
, 73
, pp. 303
–309
.10.1016/j.compstruct.2005.02.00120.
Ghiorse
, S. R.
, 1993
, “Effect of Void Content on the Mechanical Properties of Carbon/Epoxy Laminates
,” SAMPE Q.
, 24
(2
), pp. 54
–59
.21.
Boey
, F. Y. C.
, and Lye
, S. W.
, 1992
, “Void Reduction in Autoclave Processing of Thermoset Composites Part 1: High Pressure Effects on Void Reduction
,” Composites
, 23
(4
), pp. 261
–265
.10.1016/0010-4361(92)90186-X22.
Muller de Almeida
, S. F.
, and dos Santos Nogueira Neto
, Z.
, 1994
, “Effect of Void Content on the Strength of Composite Laminates
,” Compos. Struct.
, 28
, pp. 139
–148
.10.1016/0263-8223(94)90044-223.
Hamidi
, Y. K.
, and Altan
, M. C.
, 2003
, “Spatial Variation of Void Morphology in Resin Transfer Molded E-Glass/Epoxy Composites
,” J. Mater. Sci. Lett.
, 22
, pp. 1813
–1816
.10.1023/B:JMSL.0000005428.88229.5b24.
Blackmore
, B.
, Li
, D.
, and Gao
, J.
, 2001
, “Detachment of Bubbles in Slit Microchannels by Shearing Flow
,” J. Colloid Interface Sci.
, 241
(2
), pp. 514
–520
.10.1006/jcis.2001.775525.
Barraza
, H. J.
, Hamidi
, Y. K.
, Aktas
, L.
, O'Rear
, E. A.
, and Altan
, M. C.
, 2004
, “Porosity Reduction in the High-Speed Processing of Glass-Fiber Composites by Resin Transfer Molding (RTM)
,” J. Compos. Mater.
, 38
(3
), pp. 195
–226
.10.1177/002199830403864926.
Hagstrand
, P. O.
, Bonjour
, F.
, and Månson
, J. A. E.
, 2005
, “The Influence of Void Content on the Structural Flexural Performance of Unidirectional Glass Fibre Reinforced Polypropylene Composites
,” Composites, Part A
, 36
(5
), pp. 705
–714
.10.1016/j.compositesa.2004.03.00727.
Hancox
, N. L.
, 1975
, “The Compression Strength of Unidirectional Carbon Fibre Reinforced Plastic
,” J. Mater. Sci.
, 10
, pp. 234
–242
.10.1007/BF0054034728.
Lenoe
, E. M.
, 1970
, “Effect of Voids on Mechanical Properties of Graphite Fiber Composites
,” AVSD-0166-71-RR, U.S.DOT Navy, U.S. Naval Air Systems Command
, Washington DC
.29.
Tang
, J. M.
, Lee
, I. W.
, and Springer
, G. S.
, 1987
, “Effects of Cure Pressure on Resin Flow, Voids and Mechancial Properties
,” J. Compos. Mater.
, 21
, pp. 421
–440
.10.1177/00219983870210050230.
Stringer
, L. G.
, 1989
, “Optimization of the Wet Lay-Up/Vacuum Bag Process for the Fabrication of Carbon Fibre Epoxy Composites With High Fibre Fraction and Low Void Content
,” Composites
, 20
(5
), pp. 441
–452
.10.1016/0010-4361(89)90213-9Copyright © 2012 by ASME
You do not currently have access to this content.
