1-10 of 10
Keywords: machine tools
Close
Sort by
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Tribol. October 2009, 131(4): 042201.
Published Online: September 23, 2009
... phenomena involved. Utilizing the shear factor as an analysis parameter, the parameters that significantly influence the friction in microscale machining processes were ascertained and discussed. 17 10 2007 06 05 2009 23 09 2009 brass friction machine tools mechanical contact...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Tribol. April 2008, 130(2): 021601.
Published Online: March 3, 2008
... strokes can be readily determined by the corresponding successive mapping of matrix operations. Literatures are numerous to guide the manufacturers as to how to reach a specified surface roughness via proper selection of the finishing method, the machine tools, and operational precautions ( 1 2 3...
Journal Articles
Publisher: ASME
Article Type: Technical Papers
J. Tribol. July 2003, 125(3): 649–660.
Published Online: June 19, 2003
... machine tools machining sliding friction adhesion optical images image resolution The nature of contact between chip and tool rake face has a major influence on the mechanics of machining. Any change in the frictional conditions at this interface can result in a change in the chip-tool...
Topics: Cutting, Metals
Journal Articles
Publisher: ASME
Article Type: Technical Papers
J. Tribol. April 2003, 125(2): 391–402.
Published Online: March 19, 2003
... the seal system. seals (stoppers) mechanical contact machine tools lubrication tribology dynamic response performance evaluation 27 October 2002 05 February 2002 12 June 2002 19 03 2003 Contributed by the Tribology Division of THE AMERICAN SOCIETY OF MECHANICAL...
Journal Articles
Publisher: ASME
Article Type: Technical Papers
J. Tribol. July 2002, 124(3): 617–626.
Published Online: May 31, 2002
... metals cutting machining manufacturing processes machine tools The nature of the conditions at the chip-tool interface in machining has been the focus of considerable research. The interactions between the chip and the tool occurring at this interface control to a great extent the shear plane...
Topics: Cutting, Metals
Journal Articles
Publisher: ASME
Article Type: Technical Papers
J. Tribol. January 2002, 124(1): 166–177.
Published Online: September 27, 2001
... received by the Tribology Division May 15, 2001; revised manuscript received September 27, 2001. Associate Editor: J. Fre^ne. 22 October 2001 15 May 2001 27 September 2001 thermal analysis lubrication hydrodynamics machine tools tribology Yu and Sadeghi 1 previous...
Journal Articles
Publisher: ASME
Article Type: Technical Papers
J. Tribol. July 2001, 123(3): 469–473.
Published Online: June 29, 2000
... by the Tribology Division Feb. 29, 2000; revised manuscript received June 29, 2000. Paper No. 2000-TRIB-21. Associate Editor: T. C. Ovaert. 29 Feb 2000 29 June 2000 mechanical contact tribology machine tools surface topography rough surfaces shear strength interface phenomena lubrication...
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Technical Papers
J. Tribol. July 2000, 122(3): 544–549.
Published Online: January 18, 2000
... and allowing faster cutting speeds. The metalworking fluid also reduces the friction between the tool and the workpiece, thus increasing tool life and improving the surface finish on the workpiece 1 . machining metals cutting machine tools cooling drops evaporation condensation heat transfer...
Journal Articles
Publisher: ASME
Article Type: Technical Papers
J. Tribol. January 2000, 122(1): 340–347.
Published Online: June 23, 1999
... by the Tribology Division February 2, 1999; revised manuscript received June 23, 1999. Paper No. 99-Trib-25. Associate Technical Editor: J. Williams. 10 October 1999 02 February 1999 23 June 1999 wear machine tools steel cutting machining Cutting temperature is known to play...